Show menu
Marki  i Produkty

Brands & Products

Window & Door

WINDOW & DOOR Innovative, high yield one-component polyurethane foam formulated for professional filling, insulating and sealing around windows and doors. This specifically engineered, low pressure, low expansion formula eliminates warping or bowing of door and window frames. It is an AAMA Verified Component, tested according to AAMA 812. Its excellent thermal insulating properties are more efficient, labor friendly, and provide a better energy seal than fiberglass insulation. It has excellent adhesion to most common building materials. TYTAN WINDOW & DOOR is environmentally friendly, contains no CFC's or HCFC's, and it is UL Classified.

Benefits

  • Low Pressure, Low Expansion Formula Expands to Fill Gaps Without Warping, Bending, or Bowing Window and Door Frames during Installation
  • Flexible after cure – Absorbs Fenestration linear Expansion
  • High Yield product
  • AAMA Verified Component for use in Window and Door installation
  • Provides Excellent Dimensional Stability – Exceeds AAMA 812 Requirements
  • Bond and Seals to Common Construction Materials, Wood, Concrete, Plaster, etc.
  • Controllable, Quick, and Efficient Application
  • Repels and Deflects Moisture
  • Durable Airtight Seal – Bonds, Stops Air Infiltration, and Heat Loss
  • High Thermal Insulation Value - Increases Energy Efficiency (R value 4-5 per inch)
  • Easier to Transport and Use than Fiberglass
  • Shelf Life - 12 Months
  • Application instruction

    Always read all operating, application, and safety instructions before using any products from Selena Group. Use in conformance with all local, state, and federal regulations and safety requirements. Read all product directions and safety information before use.

    Preparation 

    • Product FLAMMABLE DURING DISPENSING.
    • Wear protective clothes, gloves, and eye protection. Use only in well ventilated area or wear approved respiratory equipment. Contact and application areas should be dry, clean, free of dust, oil, grease or any foreign objects, debris and contaminants that could interfere with proper adhesion. Clean and degrease surface with TYTAN™ Cleaner, acetone, isopropanol, ethanol (metals, glass) or detergent (plastics), and let it dry completely. Surfaces must be sound and in good condition. It is recommended to lightly spray surfaces with water prior to applying foam to enhance expansion and curing properties.
    • For best results and maximum yield, apply at temperatures 50oF to 86oF/ 10oC - 30oC. Use below 41oF /5oC is not recommended.
    • Shake the can vigorously for 30-45 seconds before attaching to recommended TYTAN Foam Gun and also in-between uses.
    • Remove protective cap, invert can, and screw the can firmly onto the recommended TYTAN gun - do not over tighten.

    Application 

    • Maintain the can in upside-down, inverted position during the application.
    • Point gun in safe direction and slowly pull trigger to test dispense foam. Adjust control knob on gun handle to achieve the desired application flow.
    • Fill cavities to approximately 50% full to allow for foam expansion after application. Cracks wider than 2” should be filled gradually in layers.
    • Trim excess foam with sharp knife or serrated edge. Cured foam may be sanded, painted, or stained (not before 24 hrs. after application). Cured foam discolors and loses its stability and properties when exposed to UV light. Paint or coat exposed foam for best results.
    • If idle for 10 or more minutes between uses, shake can vigorously 30-45 seconds before reusing.
    • When not in use, gun valve should be cleaned with TYTAN CLEANER.

    Cleaning 

    • Clean Foam Gun thoroughly with TYTAN CLEANER immediately after use to prevent foam from hardening in gun.
    • Uncured Foam – Clean immediately with TYTAN CLEANER or acetone.
    • Cured Foam - if hardened on skin - use an industrial cleaner with pumice. Repeat process until foam is removed. Cured foam must be mechanically removed or allowed to wear off in time.

    Typical application

    • For interior and exterior window & door installations
    • For filling and sealing all interior and exterior building gaps, cracks, and openings
    Logo Selena

    © 2020 Selena Group. All rights reserved.