Show menu
Marki  i Produkty

Brands & Products

Outdoor & Auto

TYTAN OUTDOOR & AUTO PRO is a ready to use, easy to apply, one-component polyurethane foam specially formulated to fill, insulate and seal gaps, cracks, openings and blend in with automotive undercarriages and outdoor landscaping applications. The OUTDOOR & AUTO PRO formula creates a durable airtight seal, stops air infiltration, pests, and saves energy. It provides excellent adhesion to most surfaces and materials including metal, wood, glass, masonry and plastic. It is environmentally friendly, contains no CFC's or HCFC's and it is UL listed.


  • Designed to Insulate, Seal and Blend in with RV Undercarriages  
  • Reduces Sound and Noise 
  • High Insulation Value - Increases Energy Efficiency 
  • Controllable and Efficient Application  
  • Repels and Blocks Moisture 
  • Durable Airtight Seal - Stops Air Infiltration, Dust, Pests and Insects 
  • Strong Adhesion Quality - Bonds to Most Surfaces  
  • Great for Outdoor Landscaping Applications 
  • Safe for windows and doors 
  • Shelf Life - 12 Months 

Application instruction

Always read all operating, application, and safety instructions before using any products from Selena Group. Use in conformance with all local, state, and federal regulations and safety requirements. Read all product directions and safety information before use. 


  • Wear protective clothes, gloves, and eye protection. Use only in well ventilated area or wear approved respiratory equipment. Contact and application areas should be dry, clean, free of dust, oil, grease or any foreign objects, debris and contaminants that could interfere with proper adhesion. Clean and degrease surface with TYTAN™ Cleaner, acetone, isopropanol, ethanol (metals, glass) or detergent (plastics), and let it dry completely. Surfaces must be sound and in good condition. It is recommended to lightly spray surfaces with water prior to applying foam to enhance expansion and curing properties.  
  • For best results and maximum yield, apply at temperatures 50oF to 86oF/ 10oC - 30oC. Use below 50oF /5oC is not recommended.  
  • Shake the can vigorously for 30-45 seconds before attaching to recommended TYTAN Foam Gun and also in-between uses.  
  • Remove protective cap, invert can, and screw the can firmly onto the recommended TYTAN gun - do not over tighten. 


  • Maintain the can in upside-down, inverted position during the application.  
  • Point gun in safe direction and slowly pull trigger to test dispense foam. Adjust control knob on gun handle to achieve the desired application flow. 
  • Fill cavities to approximately 50% full to allow for foam expansion after application.  Cracks wider than 2” should be filled gradually in layers. 
  • Trim excess foam with sharp knife or serrated edge. Cured foam may be sanded, painted, or stained (not before 24 hrs. after application). Cured foam discolors and loses its stability and properties when exposed to UV light.  Paint or coat exposed foam for best results. 
  • If idle for 10 or more minutes between uses, shake can vigorously 30-45 seconds before reusing.  
  • When not in use, gun valve should be cleaned with TYTAN CLEANER. 


  • Clean Foam Gun thoroughly with TYTAN CLEANER immediately after use to prevent foam from hardening in gun.  
  • Uncured Foam – Clean immediately with TYTAN CLEANER or acetone.  
  • Cured Foam - if hardened on skin - use an industrial cleaner with pumice. Repeat process until foam is removed. Cured foam must be mechanically removed or allowed to wear off in time. 

Typical application

  • Wide Range of RV and Landscaping Applications:
  • Fill and Seal Building Gaps, Cracks and Penetrations
  • Fill and Seal Rock Walls
  • Fill Gaps and Cracks in the Sidewalks and Porches
  • Fill, Seal and Insulate Around HVAC Units
  • Fill and Seal Around Utility Panels, Pipes, Air Vents, Electrical or Hatch Access
  • Seals Against Dust, Pests or Air Infiltration
Logo Selena

© 2020 Selena Group. All rights reserved.