Show menu
Marki  i Produkty

Brands & Products

Fill All

TYTAN Fill All PRO is an innovative, low-pressure, interior & exterior sealant that can be used for every gap-filling project. TYTAN Fill All PRO’s unique all-in-one high yield formula will seal every gap or crack from ¼”-3”. It offers superior R-value which reduces energy consumption and contributes to LEED energy saving standards. It has premium adhesion abilities to most construction materials including: wood, metal, masonry, glass, and most plastics so your gaps and cracks will stay sealed during construction and climate changes. With TYTAN Fill All PRO Insulating Foam Sealant you can Build with Confidence!

Benefits

  • Fills gaps ¼-3”
  • Economically insulates, fills, seals, and bonds
  • Durable weather seal- stops cold air infiltration and heat loss
  • High insulation value- saves energy and money
  • Bonds and seals popular materials: wood, concrete, plaster, plumbing, etc.
  • May be used in as low as 32⁰F
  • Shelf Life- 12 Months

Application instruction

Always read all operating, application, and safety instructions before using any products from Selena Group. Use in conformance with all local, state, and federal regulations and safety requirements. Read all product directions and safety information before use. 

Preparation 

  • Product FLAMMABLE DURING DISPENSING.  
  • Wear protective clothes, gloves, and eye protection. Use only in well ventilated area or wear approved respiratory equipment. Contact and application areas should be dry, clean, free of dust, oil, grease or any foreign objects, debris and contaminants that could interfere with proper adhesion. Clean and degrease surface with TYTAN™ Cleaner, acetone, isopropanol, ethanol (metals, glass) or detergent (plastics), and let it dry completely. Surfaces must be sound and in good condition. It is recommended to lightly spray surfaces with water prior to applying foam to enhance expansion and curing properties.  
  • For best results and maximum yield, apply at temperatures 32oF to 86oF/ 0oC - 30oC. Use below 14oF /-10oC is not recommended.  
  • Shake the can vigorously for 30-45 seconds before attaching to recommended TYTAN Foam Gun and also in-between uses.  
  • Remove protective cap, invert can, and screw the can firmly onto the recommended TYTAN gun - do not over tighten. 

Application 

  • Maintain the can in upside-down, inverted position during the application.  
  • Point gun in safe direction and slowly pull trigger to test dispense foam. Adjust control knob on gun handle to achieve the desired application flow. 
  • Fill cavities to approximately 50% full to allow for foam expansion after application.  Cracks wider than 2” should be filled gradually in layers. 
  • Trim excess foam with sharp knife or serrated edge. Cured foam may be sanded, painted, or stained (not before 24 hrs. after application). Cured foam discolors and loses its stability and properties when exposed to UV light.  Paint or coat exposed foam for best results. 
  • If idle for 10 or more minutes between uses, shake can vigorously 30-45 seconds before reusing.  
  • When not in use, gun valve should be cleaned with TYTAN CLEANER. 
  • Cleaning 

    • Clean Foam Gun thoroughly with TYTAN CLEANER immediately after use to prevent foam from hardening in gun.  
    • Uncured Foam – Clean immediately with TYTAN CLEANER or acetone.
    • Cured Foam - if hardened on skin - use an industrial cleaner with pumice. Repeat process until foam is removed. Cured foam must be mechanically removed or allowed to wear off in time. 

Typical application

  • Wide range of interior and exterior sealing and insulating applications such as basements, roof areas, plumbing, electrical, heating and cooling penetrations: 
  • excellent to fill and seal all interior and exterior building gaps, cracks, and openings
  • excellent to fill and seal in exposed corner T-joint and studs 
  • excellent to fill and seal around dryer and exhaust vents, water faucets, plumbing fixtures, electric, HVAC and gas penetrations
  • excellent to seal and insulate under the edges of exposed siding along foundations 
Logo Selena

© 2020 Selena Group. All rights reserved.