Show menu
Marki  i Produkty

Brands & Products

Bond All Foam Adhesive

TYTAN BOND ALL FOAM ADHESIVE PRO is a ready to use, one component, polyurethane based foam adhesive.  It has excellent adhesion to drywall, vinyl-faced wallboard, styrofoam, masonry, lumber, cork, wood, steel studs, and other common construction materials. TYTAN BOND ALL FOAM ADHESIVE PRO is superior to traditional adhesive because of its excellent bonding power to dry, frozen, and damp surfaces. One 24oz aerosol can replaces 12 cartridges of traditional caulk adhesive and reduces the typical time for installation by 50%. TYTAN BOND ALL FOAM ADHESIVE PRO insulates, reduces noise transmission, and prevents energy loss. TYTAN BOND ALL FOAM ADHESIVE PRO is an environmentally friendly formula that does not contain R22, CFCs and is Formaldehyde Free.  It is also UL listed. 

Benefits

  • Highly cost effective - replaces up to 12 cartridges of traditional caulk adhesive. 
  • Meets the requirements of ASTM D 6464-03a 
  • Saves money, time, and effort. 
  • Superior adhesion – can be applied to dry, wet, or frozen surfaces. 
  • Eliminates need for nails and unsightly nail pops. 
  • Added thermal and sound insulation. 
  • Application temperature from 41 OF 
  • Shelf life 18 months 

Application instruction

Always read all operating, application, and safety instructions before using any products from Selena Group. Use in conformance with all local, state, and federal regulations and safety requirements. Read all product directions and safety information before use. 

Preparation 

  • Product FLAMMABLE DURING DISPENSING.  
  • Wear protective clothes, gloves, and eye protection. Use only in well ventilated area or wear approved respiratory equipment. Contact and application areas should be dry, clean, free of dust, oil, grease or any foreign objects, debris and contaminants that could interfere with proper adhesion. Clean and degrease surface with Tytan Cleaner, acetone, isopropanol, ethanol (metals, glass) or detergent (plastics), and let it dry completely. Surfaces must be sound and in good condition. It is recommended to lightly spray surfaces with water prior to applying foam to enhance expansion and curing properties.
  • For best results and maximum yield, apply at temperatures 50oF to 86oF/ 10oC - 30oC. Use below 41oF /5oC is not recommended.  
  • Shake the can vigorously for 30-45 seconds before attaching to the Tytan Gun and also in-between uses.  
  • Remove protective cap, invert can, and screw the can firmly onto the gun - do not over tighten.  

Application 

  • Maintain the can in upside-down inverted position during the application 
  • Point the gun in safe direction and slowly pull trigger to test dispense foam. Adjust control knob on gun handle to achieve desired application flow. 
  • Pull trigger to dispense adhesive, controlling the extrusion rate with trigger pressure. The applicator trigger may be adjusted by turning the round knob at the rear of the applicator dispenser 
  • Dispense a uniform 3/8” –1/2” bead on the center of all joints and apply two beads side by side or one larger ½” bead in zig-zag pattern where panels butt together. For best results, allow Bond All Foam Adhesive Pro to flatten for 3 minutes before attaching sheathing. Minimize gaps between substrates immediately by applying pressure.  Minimum time for initial holding power is 2 hours; full bond time is 5 days. 
  • Do not pull apart sheathing once it is set in place.  Materials must be additionally mechanically fastened to insure permanent bond. 
  • When not in use, gun valve should be cleaned with Tytan Cleaner  

Cleaning 

  • Clean the Tytan Gun thoroughly with Tytan Cleaner immediately after use to prevent foam from hardening in gun.  
  • Uncured Foam - Clean immediately with Tytan Cleaner. 
  • Cured foam - if hardened on skin - use an industrial cleaner with pumice. Repeat process until foam is removed. Cured foam must be mechanically removed or allowed to wear off in time. 

Typical application

  • Adhering drywall on studs and furring strips 
  • Adhering boards to concrete or plywood 
  • Gluing small and large elements to Styrofoam, concrete, metals, masonry, steel, fiberglass, plastics and more 
Logo Selena

© 2019 Selena Group. All rights reserved.